VMP Mounts and Accessories

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The FP-LF is a fixed, flat panel wall mount that can handle most displays 42" to 63". The unit is easy to install, has a heavy load capacity of 180 lbs., mounts less then 2" off the wall, and comes in either silver or black powder coat finish. The rails of the FP-LF can slide left to right for perfect flat panel placement.

• Holds most 42" - 63" flat panels
  Distance from wall to the back of the monitor - 1.4"
• Adjustable mounting rails accommodate up to a 850mm x 500mm hole pattern
• Accommodates double gang box
• Load capacity - 180 lbs
• Silver or Black powder coat finish

Cut sheet in PDF

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The FP-LFVB is a large flush panel mount that accommodates most 42" to 63" flat panels. This low profile mount is less then 1" off the wall and takes into account the new LCD panels that are thin and light. Easy to install, but able to hold up to 150 lbs. The FP-LFVB comes in either black or silver powder coat.

• Holds most 42" - 63" flat panels
• Maximum flat panel hole pattern - 890mm x 540mm
• Distance from wall to back of the flat panel - 0.85"
• Load capacity - 150 lbs
• Silver or Black powder coat finish

Technical Drawing

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The FP-XMF is an extra medium flush panel mount that accommodates most 32" to 52" flat panels. This low profile mount is less then 1" off the wall and takes into account the new LCD panels that are thin and light. Easy to install, but able to hold up to 150 lbs.  The FP-XMF comes in either black or silver powder coat.

• Holds most 32" - 52" flat panels
• Maximum flat panel hole pattern - 640mm x 430mm
• Distance from wall to back of the flat panel - 0.85"
• Load capacity - 150 lbs
• Silver or Black powder coat finish

Technical Drawing

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The FP-XMFT is a mid-size flat panel mount with tilt that will handle most flat panels 32" to 52". Adjustable rails and tilt make flat panel placement easy to set. The FP-XMFT can handle up to 120 lbs and mounts less then 2.3" off the wall. The open back design allows for easy management behind the panel.

• Holds most 32" - 52" flat panels
• Maximum flat panel hole pattern - 640mm x 430mm
• Adjustable tilt -5° to +15°
• Distance from wall to back of the flat panel - 2.3"
• Load capacity - 150 lbs
• Silver or Black powder coat finish

Technical Drawing

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The FP-MF is a mid size flush panel mount that accommodates most 27" to 42" flat panels. This low profile mount is less than 1" off the wall and takes into account the new LCD panels that are thin and light. Easy to install, but able to hold up to 100 lbs. The FP-MF comes in either black or silver powder coat.

• Holds most 27" - 42" flat panels
• Maximum flat panel hole pattern - 440mm x 330mm
• Distance from wall to back of the flat panel - 0.7"
• Load capacity - 100 lbs
• Silver or Black powder coat finish

Technical Drawing

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The LCD-MID-F is a fixed, flat panel wall mount that can handle most displays 27" to 42". The unit is easy to install, has a heavy load capacity of 100 lbs., mounts 1" off the wall, and comes in either silver or black powder coat finish. The rails of the LCD-MID-F can slide left to right for perfect flat panel placement.

• Holds most 27" - 42" flat panels
• Maximum flat panel hole pattern - 410mm x 340mm
• Distance from wall to back of the flat panel - 1"
• Accommodates double gang box
• Load capacity - 100 lbs
• Silver or Black powder coat finish

A&E Spec Sheet

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The FP-SFB is a small flush mount that will handle most 10" to 30" flat panels. The small, easy to use mount is less then 1" from the wall and uses VMP's quick connect/disconnect design.

• Accommodates flat panels with 75, 100, 200 and 100 x 200mm VESA standards
• Holds most 10" - 30" flat panels
• Quick connect/disconnect design
• Distance from wall to back of the flat panel - 0.5"
• Utilizes tamper resistant screws to provide extra security
• Load capacity - 50 lbs
• Black powder coat finish

Technical Drawing

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The FP-LDSB is an adjustable digital signage mount that can hold most flat panels 32" to 63". This versatile mount can be used in either portrait or landscape, has adjustable and lockable tilt and moveable rails allowing perfect panel placement. The FP-LDSB can also be used with a sectional wall plate to create a video wall.

• Holds most 32" - 63" flat panels in portrait or landscape
• Maximum flat panel hole pattern - 810mm x 530mm (810mm x 810mm with extensions)
• Adjustable tilt -5° to +15° lockable at 5° increments
• Sectional wall plate which can be integrated with multiple FP-LDSB's to create a video wall
• Distance from wall to back of the flat panel - 2.5" (2.6" with extensions)
• Load capacity - 180 lbs
• Black powder coat finish

Technical Drawing

A&E Spec Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The FP-SFTB is a low profile, small flat panel mount with tilt. It holds most flat panels 10" to 23" while keeping the monitor less then 2" off the wall. The FP-SFTB is easy to install and easy to use.

• Holds most 10" - 23" flat panels
• Accommodates flat panels w/ 75 or 100mm VESA standards
• Adjustable tilt -5° to +15°
• Distance from wall to back of the flat panel - 1.7"
• Utilizes tamper resistant hardware
• Load capacity - 25 lbs
• Black or Silver powder coat finish

Technical Drawing

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The LCD-MID-FT is a mid size flat panel mount with tilt. It holds most flat panels 27" to 42", has adjustable tilt while keeping it close to the wall. Rails adjust left to right and lock in place for perfect flat panel placement.

• Holds most 27" - 42" flat panels
• Maximum flat panel hole pattern - 850mm x 530mm
• Distance from wall to back of the monitor - 2.4"
• Has adjustable -5° to +15° tilt
• Accommodates double gang box
• Load capacity - 100 lbs
• Black or Silver Powder Coat finish

Cut sheet in PDF

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The PDS-LFT is a tilting mount that will handle most flat panels 42" to 63". Adjustable rails and tilt make flat panel placement easy to set. The PDS-LFT can handle up to 180 lbs and mounts less then 3" off the wall.

• Holds most 42" - 63" flat panels
• Maximum flat panel hole pattern - 850mm x 530mm
• Adjustable tilt -5° to +15°
• Distance from wall to back of the flat panel - 2.6"
• Load capacity - 180 lbs
• Black or Silver powder coat finish

Technical Drawing

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The FP-MWAB is incredibly installer friendly and a time saver by being both fully assembled and ready-to-use out-of-the-box. The FP-MWAB comes available in black powdered coat finish and has a 45 degree rotation and up to 15 degree tilt capabilities. And for the security conscious, the units' mounting rails accept padlocks for added peace-of-mind.

• Holds most 24" - 37" flat panels
• Mounts on a single stud
• Maximum flat panel hole pattern - 450mm x 400mm
• Rotates 45° left to right
• Tilt - ±15°
• List correction - ±4°
• Depth 5.5" (arms fully collapsed) / 16.5" (arms fully extended)
• Mounting rails accept padlocks
• Built in level
• Load capacity - 80 lbs
• Black powder coat finish

Cut sheet in PDF

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The FP-XMWAB is incredibly installer friendly and a time saver by being both fully assembled and ready-to-use out-of-the-box. The FP-XMWAB comes available in black powdered coat finish and has a 45 degree rotation and up to 15 degree tilt capabilities. And for the security conscious, the units' mounting rails accept padlocks for added peace-of-mind.

• Holds most 32" - 52" flat panels
• Maximum flat panel hole pattern - 800mm x 500mm
• Rotates 45° and has adjustable 0° to 15° tilt
• Depth 5.3" (arms fully collapsed)
• Depth 16.3" (arms fully extended)
• Mounting rails accept padlocks
• Includes level correction capability
• Load capacity - 130 lbs
• Silver or Black powder coat finish

Technical Drawing

Instruction Sheet

VMP's revolutionary Universal LCD Monitor Mount offers the industry's first, truly Multi-Configurable design. With the abilities to configure the LCD-1 into several different mounting styles, users can accommodate nearly every wall mount application they encounter, with just one mount! The LCD-1 works with nearly ever LCD monitor from 10"-21" that uses a 75 or 100mm VESA standard. Whether your application calls for a double arm articulating mount, a single arm mount or a near flush mount, you need look no further than the LCD-1 from Video Mount Products.

• Can be configured as a single arm, double arm articulating, or near flush mount with parts provided
• Holds most 10"-21" LCD monitors
• Accommodates monitors with 75 or 100mm VESA standards
• Adjustable -5° to +30° tilt.
• Rotates 240° at the monitor
• Rotates 160° at the wall
• Rotates 240° at the elbow joint (double arm configuration.)
• Feed through wall plate with decorative cover
• Includes clip-based cable management system
• Load capacity 25 lbs
• Available in silver powder coat or black finish

Cut sheet in PDF

Instruction Sheet

The LCD-2537 is a multi-configurable flat panel wall mount that can handle a wide variety of situations. The mount can be used as a single arm, double arm or near flush wall mount and holds most 25" to 32" flat panels.

• can be used as a single arm, double arm articulating or near flush mount with parts provided
• holds most 25" to 37" LCD monitors
• accommodates monitors with 75, 100, 200 and 100 x 200 mm VESA standards
• adjustable -5° to +30° tilt
• rotates 240° at the monitor / 160° at the wall
• rotates 240° at the elbow joint (double arm configuration)
• feed through wall plate with decorative cover
• includes clip based cable management system
• load capacity - 50 lbs
• silver or black powder coat finish

Cut sheet in PDF

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The PDS-LWA, large flat panel articulating wall mount, handles most flat panels from 52" to 63". The mount can handle multiple configurations with adjustable rotation, tilt and extendable arms. The back plate of the PDS-LWA can also move from left to right to ensure perfect placement on the wall.

• Holds most 52" - 63" flat panel displays
• Maximum flat panel hole pattern - 950mm x 530mm
• Rotates 45° and has adjustable -5° to +15° tilt
• Depth 4.3" (Arms fully collapsed)
• Depth 24" (Arms fully extended)
• Accommodates double gang box
• Load capacity - 180 lbs
• Black or Silver powder coat finish

Technical Drawing

Instruction Sheet

The LCD-1C is a versatile ceiling mount that can handle most flat panels 10" to 23". The LCD-1C allows perfect flat panel placement using adjustable mast extension, monitor rotation and tilt.

• Holds most 10" - 21" LCD Monitors
• Accommodates monitors with 75 or 100mm VESA standards
• Mast telescopes 17" - 27" from the ceiling
• Rotates 360° and has adjustable -5° to +30° tilt
• Rotates 240° at the monitor
• Includes clip based cable management system
• Load capacity 25 lbs.
• Available in Silver, Black or White powder coat finish

Cut sheet in PDF

Instruction Sheet

The LCD-2537C is a versatile ceiling mount that can handle most flat panels 25" to 37". The LCD-2537C allows perfect flat panel placement using adjustable mast extension, monitor rotation and tilt.

• Holds most 25" - 37" LCD Monitors
• Mast Telescopes from 18" - 30"
• Accommodates monitors with 75, 100, 200 and 100 x 200 mm VESA standards
• Rotates 360° and has adjustable -5° to +30° tilt
• Rotates 240° at the monitor
• Includes clip based cable management system
• Load Capacity 50 lbs
• Silver Powder Coat Finish

Cut sheet in PDF

Instruction Sheet

The LCD-MID-C is a mid size flat panel ceiling mount that can accommodate most 27" to 42" flat panels. This versatile mount can handle a wide range of ceiling applications with it's adjustable tilt, extension, rotation and rails to ensure perfect flat panel placement.

• holds most 27" - 42" LCD flat panels
• Mounting rails adjust to accommodate monitors with mounting holes up to VESA 400 x 200
• Mast Telescopes 23" – 35" from ceiling
• Rotates 360° and has adjustable -5° to +20° tilt
• Cable management through the center of the mast
• load capacity - 100 lbs.
• Black or silver powder coat finish

Cut sheet in PDF

Instruction Sheet

Complete your flush mount installation

Recessed low and high voltage boxes from Arlington Industries make flush mounting easier

Arlington's recessed two-gang TV BOX™ for old work allows you to mount LCD and plasma TVs, and other system components flush against the wall.

The PDS-LC is a large flat panel ceiling mount that can accommodate most 37" to 63" flat panels. This versatile mount can handle a wide range of ceiling applications with it's adjustable tilt, extension, rotation and rails to ensure perfect flat panel placement.

• Holds most 37" - 63" flat panels
• Maximum flat panel hole pattern - 860mm x 500mm
• Mast telescopes 23" - 35" from ceiling
• Rotates 360° / Adjustable 0° - 15° tilt
• Cable management through the center of the mast
• Load capacity - 180 lbs
• Black or Silver powder coat finish

Technical Drawing

Instruction Sheet

The ER-LCD1017 can hold most 10" to 17" flat panels on an equipment rack. It can also accommodate up to a 23" monitor by inverting the mount on the rack. The ER-LCD1017 has a static resistant powder coat finish and includes two types of rack screws.

• Accommodates Monitors with 75mm and 100mm VESA Standards
• Recesses monitor into rack
• Holds Most Monitors 10" - 17"
• Can be inverted to hold monitors up to 23"
• 9 space racking height
• Load Capacity 50 lbs.
• Mounting Screws (monitor to mount) included
• Includes 10-32 and 12-24 rack screws

A&E Spec Sheet

Technical Drawing

The LCD-UC1 holds most 10" to 17" flat panels up to 20 lbs., has tilt and swivel capabilities for optimum viewing angles, and can conveniently flip up to keep the flat panel out of view, as well as protected, when not in use.

• Holds Most 10" - 17" LCD TVs
• Accommodates monitors with 75 or 100mm VESA standards
• Can be flipped up to store LCD when not in use
• 360° swivel for optimum viewing
• Load Capacity - 20 lbs.
• Silver Powder Coat finish

A&E Spec Sheet

The LCD-2 flat panel table/desk mount holds most 10" to 23" flat panels via clamp-on or bolt. Rotatable 360 degrees, this versatile mount also tilts up to 30 degrees, making the screen visible no matter what side of the desk you are sitting on.

• Can be attached as a clamp-on or bolt through mount
• Holds most 10" - 23" LCD Monitors
• Accommodates monitors with 75 or 100mm VESA standards
• Rotates 360° and has adjustable -5° to +30° tilt
• Force arm has adjustable 0° to 60° forward tilt
• Load capacity 25 lbs.
• Silver or Black powder coat finish

A&E Spec Sheet

VMP's turntables allow the consumer the flexibility of placing the TV or monitor on a wider variety of counter tops throughout the home or office where any stable viewing vantage point is available.

• rotates 360°
• platform width 15"
• platform depth 12"
• load capacity 60 lbs
• Black finish

Instruction Sheet

VMP's turntables allow the consumer the flexibility of placing the TV or monitor on a wider variety of counter tops throughout the home or office where any stable viewing vantage point is available.

• rotates 360°
• platform width 20"
• platform depth 15"
• load capacity 75 lbs
• black finish

Instruction Sheet

VMP's turntables allow the consumer the flexibility of placing the TV or monitor on a wider variety of counter tops throughout the home or office where any stable viewing vantage point is available.

• rotates 360°
• platform width 26"
• platform depth 16"
• load capacity 125 lbs
• Black finish

Instruction Sheet

VMP's turntables allow the consumer the flexibility of placing the TV or monitor on a wider variety of counter tops throughout the home or office where any stable viewing vantage point is available.

• rotates 360°
• platform width 32"
• platform depth 18"
• load capacity 200 lbs
• black finish

Instruction Sheet

VMP's LCD turntables allow the consumer the flexibility of placing the TV or monitor on a wider variety of counter tops throughout the home or office where any stable viewing vantage point is available.

• platform width 20"
• platform depth 14"
• load capacity - 75 lbs
• Model TT-LCD20B - black finish
• model TT-LCD20S - silver finish

A&E Spec Sheet

Instruction Sheet

The LCD-CM2 adapter allows the LCD-1C to accommodate two 10quot; to 23quot; flat panels.

• adapts an LCD-1C to accommodate two LCD monitors
• holds most 10" – 23" LCD monitors
• accommodates monitors with 75 or 100mm VESA standards
• has adjustable -5° to +30° tilt and rotates 240° at monitor
• LCD-CM2 and LCD-1C combined load capacity 50 lbs

Cut sheet in PDF

The LCD-WM2 adapter allows the LCD-1 to accommodate two 10" to 23" flat panels off the wall.

• Allows attachment of 2 LCD-1 mounts (sold separately)
• Arm extends 11" from wall
• Load capacity: 50 lbs
• Silver powder coat finish

Cut sheet in PDF

The LCD-DM2 allows for two LCD-1 mounts to be attached onto a desktop via clamp-on or bolt through. Accommodates most flat panels 10" to 23" with a combined load capacity of 50 lbs.

• Allows attachment of 2 LCD-1 mounts (sold separately)
• Can be attached as a clamp-on or bolt through mount with parts provided
• Mounting pole telescopes from 18" to 24"
• Load capacity: 50 lbs
• Silver powder coat finish

Cut sheet in PDF

Instruction Sheet

The PDS-LCM2B adapter allows the PDS-LCB to accommodate two 37" to 63" flat panel displays back-to-back with a combined weight of up to 360 lbs.

• Holds most 37" - 63" flat panels
• Adapts PDS-LCB (sold separately) to accommodate 2 flat panels
• Maximum flat panel hole pattern - 860mm x 500mm
• Adjustable 0° - 15° tilt
• PDS-LCB and PDS-LCM2B combined load capacity - 360 lbs
• Black powder coat finish

Cut sheet in PDF

The LCD-MID-CM2 adapter allows the LCD-MID-C to accommodate two 27" to 42" flat panel displays back-to-back with a combined weight of up to 200 lbs.

• Adapts LCD-MID-C (sold separately) to accommodate 2 flat panels
• holds most 27" - 42" LCD flat panels
• Mounting rails adjust to accommodate monitors with mounting holes up to VESA 400 x 200
• Adjustable -5° to +20° tilt
• LCD-MID-C and LCD-MID-CM2 combined load capacity - 200 lbs.
• Black or Silver powder coat finish

Cut sheet in PDF

Instruction Sheet

The AP-1 VESA adaptor plate adapts a VESA 200mm plate to accommodate a VESA 400mm x 200mm hole pattern. Although the AP-1 has been designed specifically to work with VMP's LCD-2537 and LCD-2537C universal mid-size flat panel wall and ceiling mounts, it will work with any manufacturer's VESA 200mm mount.

• Adapts a VESA 200mm plate to accommodate a VESA 400mm x 200mm hole pattern
• Designed specifically to work with the LCD-2537 and LCD-2537C, but will work with any manufacturer's VESA 200mm mount
• Black or Silver powder coat finish

Cut sheet in PDF

Instruction Sheet

The AP-2B VESA adaptor plate adapts a VESA 200mm plate to accommodate a VESA 300mm x 300mm hole pattern. Although the AP-2B has been designed specifically to work with VMP's LCD-2537B and LCD-2537CB universal mid-size flat panel wall and ceiling mounts, it will work with any manufacturer's VESA 200mm mount.

• Adapts a VESA 200mm plate to accommodate a VESA 300mm x 300mm hole pattern
• Designed specifically to work with the LCD-2537B and LCD-2537CB, but will work w/ any manufacturer's VESA 200mm mount
• Black powder coat finish

Cut sheet in PDF

Instruction Sheet

The LCD-PA is a pole adaptor used with the LCD-1 and LCD-2537 to enable these mounts to be attached to a round or square pole.

• For use with LCD-1 and LCD-2537
• Adapts round or square poles to accept mounts
• Stainless steel straps adjust from 4" to 10"
• Silver powder coat finish

Cut sheet in PDF

Instruction Sheet

The IWB-1B is an in wall box adaptor that allows up to a 37" flat panel to fully collapse into a wall. It installs easily between two 16" on center wooden studs, has integrated cable and electrical knockouts and a high load capacity. The IWB-1B works with the LCD-1(B) and LCD-2537(B) mounts.

• Holds most 15" - 37" flat panels
• Used in conjunction with the LCD-1B or the LCD-2537B
• Fits in between two 16" on center wooden studs
• Includes paintable decorative plastic trim ring
• Integrated cable and electrical knockouts
• Flat panel collapses flush with front face
• Includes black adaptors for the LCD-1B and LCD-2537B
• Load capacity - 75 lbs

A&E Spec Sheet

Technical Drawing

The DS-BP enables the FP-LDSB digital signage mount to be extended to add additional flat panels for video walls.

• Used with the FP-LDSB to extend the wall plate 12" to add additional flat panels
• Black powder coat finish

Cut sheet in PDF

The DS-CH uses tamper resistant hardware to keep a digital signage computer secure.It easily attaches to any wall or ceiling mount in either portrait or landscape positions.

• Used to attach a digital signage computer to a wall or ceiling mount
• Attaches to mounting rails in landscape or portrait positions to better hide behind the flat panel
• Utilizes tamper resistant hardware
• Works with VMP models FP-LDSB, PDS-LC and PDS-LFT as well as most other manufacturer's mounts
• Box dimensions - 11" x 7" x 2.375"
• Black powder coat finish

Cut sheet in PDF

Instruction Sheet

The PM-1 offers a unique 8-point clamping mechanism with a 360-degree system of support allowing safe installation of expensive projectors. The PM-1 allows adjustments in height, width and depth in the projector mount giving maximum versatility for a wide variety of projectors.

• Adjustable tilt - 0° to 10°
• Adjustable yaw (Rotation) - 360°
• Opens from 10" to 24" (left to right)
• Opens from 4.5" to 7.75" (top to bottom)
• Eight-point clamping mechanism adjusts 8" to 11.75" front to back
• Mast telescopes 18" - 30" from ceiling
• Integrated flush mount plate included
• Load capacity - 75 lbs
• Black powder coat finish

Cut sheet in PDF

Instruction Sheet

Schematic

The PM-2 offers a unique 8-point clamping mechanism with a 360-degree system of support allowing safe installation of expensive projectors. The PM-2 allows adjustments in height, width and depth in the projector mount giving maximum versatility for a wide variety of projectors.

• Adjustable tilt - 0° to 10°
• Adjustable yaw (rotation) - 360°
• Opens from 7" to 13" (left to right)
• Opens from 3" to 5.75" (top to bottom)
• Eight-point clamping mechanism adjusts 6.5" to 10" front to back
• Mast telescopes 18" - 30" from ceiling
• Flush mount plate included
• Load capacity - 75 lbs
• Black powder coat Finish

Cut sheet in PDF

Instruction Sheet

The PM-3 yokeless projector mount has been designed with a high-load capacity, rugged housing, low profile, tilt, full rotation, and telescoping capabilities. It is compliant with most of today's leading projectors, and is available in silver and black powder coat finishes.

• Adjustable Tilt - ± 20°
• Adjustable Pitch - ± 15°
• Adjustable Yaw (Rotation) - ± 180° (360°)
• Fits Most Projectors with mounting holes inside 14.5" diam.
• Mast Telescopes 18" - 30" from ceiling
• Flush Mount Plate included
• Mounting screws (projector to mount) included
• Load Capacity 75 lbs.
• Silver or Black Powder Coat Finish

Cut sheet in PDF

Instruction Sheet

The PM-LP yokeless low profile projector mount has been designed with a high-load capacity, rugged housing, low profile, tilt, full rotation, and telescoping capabilities. It is compliant with most of today's leading projectors, and is available in silver and black powder coat finishes

• Low 2.625" mounting profile (measurement includes the mounting feet)
• Adjustable Tilt - ± 20°
• Adjustable Pitch - ± 15°
• Adjustable Yaw (Rotation) - 360°
• Fits Most Projectors with mounting holes inside 14.5" diameter
• 1.5" NPT Mast Telescopes 23" - 35" from ceiling
• Flush Mount Plate included
• Mounting screws (Projector to Mount) included
• Load Capacity 75 lbs.
• Silver or Black Powder Coat Finish

Cut sheet in PDF

Instruction Sheet

Protect your projectors with the PMC-L. Perfect for schools, gyms and other locations where security is important, the PMC-L provides security from theft and vandalism. It accommodates larger projectors using the PM-1, PM-3 and PM-LP.

• Inner dimensions - 24"W x 20"D x 13"H
• Lift off lid for installation
• Easy access hinge for maintenance
• Utilizes tamper resistant screws
• Adjustable front security bars for lens placement
• Accommodates PM-1, PM-3 and PM-LP
• Black powder coat finish

Cut sheet in PDF

Instruction Sheet

Protect your projectors with the PMC-S. Perfect for schools, gyms and other locations where security is important, the PMC-S provides security from theft and vandalism. It accommodates the small projectors using the PM-2, PM-3 and PM-LP.

• Inner dimensions - 16"W x 16"D x 10"H
• Lift off lid for installation
• Easy access hinge for maintenance
• Utilizes tamper resistant screws
• Adjustable front security bars for lens placement
• Accommodates PM-2, PM-3 and PM-LP
• Black powder coat finish

NOTE: Projector and mount not included

Cut sheet in PDF

Instruction Sheet

The DVR-LB1 has been designed specifically for the peace of mind of those who require DVRs be installed in specific settings that may be prone to theft or vandalism.

• Interior dimensions 21" W x 21" D x 8" H
• Vented and includes fan for additional ventilation
• Interlocking lift off lid
• Key locked hinged front door
• Black static resistant powder coat finish

Cut sheet in PDF

The DVR-LB2 is an alternative to the popular DVR-LB1 DVR lockbox. The DVR-LB2 features all the benefits of the DVR-LB1, but also includes a smoked Plexiglas window that allows IR signal pass-through.

• Interior dimensions 21" W x 21" D x 8" H
• Window dimensions are 18" W x 3" H
• Window will pass IR signals
• Vented and includes fan for additional ventilation
• Interlocking lift off lid
• Key locked hinged front door
• Black static resistant powder coat finish

Cut sheet in PDF

The DVR-WA are a pair of heavy duty, easy to install DVR lockbox wall mounting arms.

• Designed to mount to 16" on center studs
• Works with the DVR-LB1 and DVR-LB2
• Load capacity - 50 lbs
• Black static resistant powder coat finish

Cut sheet in PDF

Instruction Sheet

The LCD-PV kit comes with a LCD-2537CB, plumbing pipe adaptors for extended drops and a camera mounting bracket. With a heavy load capacity and adjustable rotation and tilt; the LCD-PV is a perfect solution for public view applications.

NOTE: Cameras and monitor not included.

Kit Includes:

• LCD-2537CB
  • Holds most LCD monitors 10" - 37"
  • Modified with two mounting points for camera bracket
  • Rotates 360° / Adjustable tilt -5° to +20°
  • Mast telescopes from 18" - 30"
  • Load capacity - 75 lbs
  • Black powder coat finish
• AK-1 & CP-1
  • Used together, these units allow ceiling to mount extension drop distances of almost any length using standard 1.5" N.P.T. plumbing pipe
• Universal Camera Bracket
  • Can be assembled into several different configurations uses industry standard 1/4" - 20 threading

Cut sheet in PDF

Instruction Sheet

VMP's full line of residential mounting solutions are not only practical, but look great in any room in the home. Rugged and with 180 degree swivel and twist capability from the wall or the ceiling, the SP-001 will project your speaker's audio with both durability and contemporary styling in mind.

• mounts on back of speaker
• swivels 180°
• twists 180°
• load capacity 12 lbs
• sold in pairs
• black finish

VMP's full line of residential mounting solutions are not only practical, but look great in any room in the home. Wall mountable and rugged with swivel and twist capability, the SP-007 will project your speaker's audio with both durability and contemporary styling in mind.

• accommodates up to 12"x12" speakers
• swivels 180°
• plate size 6"x6"
• load capacity 12 lbs.
• sold in pairs
• black finish

VMP's full line of residential mounting solutions are not only practical, but look great in any room in the home. Wall mountable and rugged with swivel and tilt capability, the SP-010 will project your speaker's audio with both durability and contemporary styling in mind.

• adjustable to fit 7" to 12" depth speakers
• swivels 90°
• and has adjustable 0 - 20° tilt
• load capacity 20 lbs.
• sold in pairs
• black finish

VMP's full line of residential mounting solutions are not only practical, but look great in any room in the home. Wall mountable and rugged with swivel and tilt capability, the SP-013 will project your speaker's audio with both durability and contemporary styling in mind.

• accommodates up to 12"x12" speakers
• swivels 135°
• and has adjustable 0 - 20° tilt
• plate size 6"x6"
• load capacity 20 lbs.
• sold in pairs
• black finish

VMP's full line of residential mounting solutions are not only practical, but look great in any room in the home. With virtually limitless range due to full range tilt, swivel, and twist, the rugged SP-200W and SP-200B wall and ceiling mounts will project your speaker's audio with both durability and contemporary styling in mind.

• virtually limitless number of configurations
• full range of tilt, twist and swivel
• wall or ceiling mount
• mounts on back of speaker
• load capacity - 12 lbs.
• high impact plastic
• Available in Black or White
• Sold in pairs

Sleek and stylish. VMP's full line of adjustable surround sound speaker stands are not only practical, but look great in any room in the home. Hidden cable management and with durability in its design, the SS-2 will project your speaker's audio with contemporary styling also in mind.

• Adjustable Height of 32" - 44" with twist lock mechanism
• Hidden Cable management through inside of support column
• Includes 2 universal speaker mounting plates to adapt to nearly every speaker
• Heavy Die Cast base
• Includes adjustable spikes for carpet and rubber feet for hard floors
• Silver Finish
• Supports up to 7 lbs.
• Sold in Pairs

Sleek and stylish. VMP's full line of adjustable surround sound speaker stands are not only practical, but look great in any room in the home. Hidden cable management and with durability in its design, the SS-3 will project your speaker's audio with contemporary styling also in mind.

• fixed 40" height
• Hidden Cable management through inside of support column
• Includes 3 universal speaker mounting plates to adapt to nearly every speaker
• Includes adjustable spikes for carpet and rubber feet for hard floors
• Silver Finish
• Supports up to 7 lbs.
• Sold in Pairs

The DLP-2 is a great way to wall mount most DLP televisions. This easy to install three bracket system has a heavy load capacity while keeping a low profile.

• Unique 3 bracket system provides under and/or over mounting
• Works with most DLP TVs
• Adjusts from 14" - 20" front to back
• Includes anti-skid pads
• Low profile hideaway design
• Load capacity - 125 lbs
• Black powder coat finish

Cut sheet in PDF

The FRM-Series is a non-penetrating roof mount for DBS, off air antenna, satellite internet systems and surveillance cameras. Using standard 8" x 8" x 16" cinderblocks as ballast the FRM-Series provides a good way to mount your equipment without damaging your roofing surface.

• 60" Mast with 1.25" O.D.

A&E Spec Sheet

Instruction Sheet

Technical Drawing

The FRM-Series is a non-penetrating roof mount for DBS, off air antenna, satellite internet systems and surveillance cameras. Using standard 8" x 8" x 16" cinderblocks as ballast the FRM-Series provides a good way to mount your equipment without damaging your roofing surface.

• 30" Mast with 1.66" O.D.

A&E Spec Sheet

Instruction Sheet

Technical Drawing

The FRM-Series is a non-penetrating roof mount for DBS, off air antenna, satellite internet systems and surveillance cameras. Using standard 8" x 8" x 16" cinderblocks as ballast the FRM-Series provides a good way to mount your equipment without damaging your roofing surface.

• 30" Mast with 2" O.D.

A&E Spec Sheet

Instruction Sheet

Technical Drawing

The PRM-2 is the perfect mount when mounting most standard DBS dishes directly to the roof is not possible. The heavy duty mount is easy to install and has an adjustable mounting plate for perfect satellite dish placement.

• Accommodates 18" and 24" DBS/DSS antennas
• Holds up to eleven 8" x 8" x 16" standard concrete blocks for ballast or comes w/ pitch pad kit
• Adjustable dish mounting plate
• Heavy duty steel construction
• Dark gray weather resistant powder coat finish

Instruction Sheet

The FRMA is an adaptor to convert an FRM-200 to a 2.375" OD masting. Simple to install and use the FRMA just slides over and existing assembled FRM-200 mast to convert the mast to a larger OD.

• Adapts FRM-200 mount (2" OD masting) to 2.375" OD masting
• Dark gray weather resistant powder coat finish

Cut sheet in PDF

The TR-Series is a heavy duty tripod for antenna masting. With installer friendly front facing feet, pitch pad kits and mast support to keep the bottom of the mast off the roofing surface if you so desire, the TR-Series secure and easy way to mount your antennas to a roof.

Individually boxed.

Instruction Sheet

Wall bracket mounts antenna or DBS pipe 3" off wall.

Accommodates 1" - 3" antenna or DBS pipe.

The WB-6 are antenna mast holders to mount on a wall. Providing a 6" clearance to the antenna mast, the WB-6 are a good way to mount your antenna and keep it stable.

• "U" bolt mast holder with 6" clearance
• Accommodates 1.25" to 1.66" antenna or DBS pipe
• Sold in pairs

The Y-MOUNT is a chimney mount for antenna or DBS pipe. Designed to be strapped around round chimneys, the Y-MOUNT provides a simple secure way to mount antennas or DBS pipes to chimneys.

• Accommodates 1.25" to 1.66" antenna or DBS pipe
• Includes 0.75" by 18' anodized steel straps
• Sold in pairs

Instruction Sheet

The GEM-1 is a gable mount for DBS dishes. It attaches to the standard footplate of a DBS dish to allow the installation of the dish on the gable of a house. The rotation capability of the GEM-1 allows you to install the mount at the angle you need while allowing you to keep the dish in an upright position.

Instruction Sheet

The Z-MOUNT is a chimney mount for antenna or DBS pipe. Designed to be strapped around square or rectangle chimneys, the Z-MOUNT provides a simple secure way to mount antennas or DBS pipes to chimneys.

• Accommodates 1.25" to 1.66" antenna or DBS pipe
• Includes 0.75" by 18' anodized steel straps
• Sold in pairs

Instruction Sheet

The GEM-4060 is a gable mount for off air antennas. The bottom portion of the GEM-4060 is adjustable allowing you to secure further down the antenna to provide more stability.

• Mounting bracket adjusts from 40° to 60° (left to right)
• Holds up to a 1.5" antenna mast

Instruction Sheet

The P-6 are a pair of mounting attachments for vent pipes that work with both antenna and DBS pipes.

• Mounting attachment for vent pipes 2.75" to 5" O.D.
• Accommodates 1" to 2" antenna or DBS pipe
• Sold in pairs

Instruction Sheet

The SM-1 is a siding mount for DBS dishes. The nesting design allows the SM-1 to create a stable flat surface to mount the footplate of a DBS dish.

• Accommodates the mounting of a DBS dish on house siding.
• Creates a flat mounting platform for the DBS foot plate by "nesting" against the siding.
• Includes mounting hardware.
• Constructed of heavy-duty "DBS gray" plastic.

Instruction Sheet

The AK-1 is an easy to use adaptor that converts VMP mounts to use 1.5" NPT pipe for longer installation ceiling drops.

AK-1

• Adaptor Kit for VMP014/024, VMP036/038, PM Series, LCD-MID-C and LCD-2537C to be used with standard 1.5" NPT pipe
• Black powder coat finish

AK-2

Adaptor Kit for VMP042/044, VMP046/048, and LCD-1C to be used with standard 1" NPT pipe

A&E Spec Sheet: AK-1

A&E Spec Sheet: AK-2

Instruction Sheet

The AK-1PT is an easy to use adaptor that converts VMP mounts to use 1.5" NPT pipe for longer installation ceiling drops. The unit works like the AK-1, but incorporates a cable pass through.

• Adaptor Kit for VMP014/024, VMP036/038, PM Series, PDS-LC, LCD-MID-C and LCD-2537C to be used with standard 1.5" NPT pipe
• Cable pass-through allows cable management through center of masting

Cut sheet in PDF

Instruction Sheet

The LVMP-1 allows wall plates to be installed anywhere by doing away with the need for an electrical junction box.

• Does away with the need for an electrical junction box
• Perfect for low voltage class 2 wiring
• Mounts any standard low voltage device
• Works with 1/2" - 1-1/4" walls
• Installs with a screwdriver and a drywall saw
• Mounting screws included

The SCFR-1 is an easy to use finishing ring that easily clamps around both 1.5" NPT pipe and VMP ceiling masts that are not 1.5".

• Finishing ring to clamp around 1.5" NPT pipe
• Includes an adaptor for VMP ceiling masts that are not 1.5" NPT pipe
• Chrome finish

Cut sheet in PDF

Instruction Sheet

The SCM-1 is a suspended ceiling tray for ceiling mounts. The SCM-1 can be used with any VMP ceiling mount or any ceiling mount using 1.5" NPT pipe. Can be used to support projectors, flat panels or CCTV under 75 lbs. Tie wire, turnbuckles and attachment hardware included.

• For use with 2' x 2' or 2' x 4' ceiling tiles
• Can be used with standard 1.5" NPT pipe or VMP ceiling masts and includes 20 feet of tie wire
• Four integrated standard electrical KOs
• Load capacity - 75lbs
• White powder coat finish

Cut sheet in PDF

Instruction Sheet

A cathedral ceiling adaptor which works with the standard mast of the VMP014/024, VMP036/038, PM Series, LCD-2537C and PDS-LC or any mount which uses a 1.5" NPT mast.

• Designed for angled ceiling installations and works with all manufacturer's mounting systems when using standard 1.5" NPT pipe
• Also works with ceiling mast provided with VMP014/024, VMP036/038, PM Series, LCD-2537C and PDS-LC
• Black powder coat finish

Cut sheet in PDF

The UA-1 is an easy to use device to adapt any VMP ceiling mount to a piece of Uni-strut®. It can also be used with other mounting brands that use a 1.5" NPT pipe.

• Adapts ceiling mounts to work w/ Unistrut up to 1.625"
• Works with ceiling masts provided with the VMP014/024, VMP036/038, PM Series, LCD-2537C and PDS-LC
• Will also work with all manufacturer's mounting systems when using 1.5" NPT pipe
• Black powder coat finish

A&E Spec Sheet

Instruction Sheet

The CP-1 and the CP-2 are universal ceiling mount plates that will accommodate 1.5" and 1" NPT pipe. Used for extending ceiling drop lengths; the CP-1/CP-2 has multiple, pre drilled hole patterns to attach to a variety of ceilings.

CP-1

• Universal ceiling flange works with all manufacturer's mounting systems when using standard 1.5" NPT pipe
• Provides base for ceiling installations
• Black powder coat finish

CP-2

• Same as above except for use w/ 1" NPT pipe

A&E Spec Sheet: CP-1

A&E Spec Sheet: CP-2

Schematic

The UP1 allows for 2 stud or joist span to distribute the mount and equipment weight evenly.

• 12" and 16" centers with threaded hole patterns for VMP-006, VMP014/024, VMP036/038 (ceiling only), VMP046/048 (wall only), and PDS-LC allows for 2 stud/joist span to distribute mounting system and equipment weight evenly
• Black powder coat finish

The CP-1PT is a universal ceiling mount plate that will accommodate 1.5" NPT pipe. Used for extending ceiling drop lengths; the CP-1PT has multiple, pre drilled hole patterns to attach to a variety of ceilings with cable pass-through.

• Universal ceiling flange works with all manufacturer's mounting systems when using standard 1.5" NPT pipe
• Cable pass-through for easy cable management
• Provides base for ceiling installations
• Black powder coat finish

A&E Spec Sheet

The VH-001 is an electronic component holder that attaches to many of VMP's CRT mounts. Combined with a VH-004B, the VH-001 can be attached to VMP flat panel ceiling mounts. With a sturdy wrap around design you can be sure your equipment will be held well.

• holds most front-load vcr's, dvd players & satellite receivers
• opens from 10.75" - 17.75" (left to right)
• top clamp adjusts from 3" - 5.375" (top to bottom)
• overall height is 5.875" (inside to inside)
• for use with ALL VMP Mounting Systems including security monitor mounts and visionary series mounts
• black or silver powder coat finish

Cut sheet in PDF

Instruction Sheet

Schematic

The VH-002 is an add-on holder for the VH-001. The VH-002 allows for a second electronic component be installed below a VH-001.

• allows a second device (vcr/dvd player, satellite receiver) to be attached to the VH-001
• black finish

Cut sheet in PDF

Schematic

The VH003 wall mount component holder is a stylish way to hold DVD players, DVR's, HD receivers, CD players, VCR's and gaming systems (Xbox 360, Playstation 3, Nintendo Wii). The mount can be used for a single device or "stacked" for use with multiple devices. Integrated cable management system hides all cables for a clean look.

• Can be used for holding a single device or "stacked" for multiple components
• Accommodates DVD players, CD players, DVRs, HD receivers and VCRs
• Mounting ring extends 12" from the wall
• Can be used in conjunction with any TV wall mount to design an entertainment center
• Load capacity – 25 lbs
• Black powder coat finish

Cut sheet in PDF

Instruction Sheet

The VH-004 is an adaptor to allow an electronic component holder to be hung underneath a VMP flat panel ceiling mount. Combined with the VH-001S, the VH-004 allows for adjustable drop distance so your electronic component can be just below your ceiling mounted flat panel.

• Allows VH-001 to be hung below VMP's flat panel ceiling mounts
• Drop adjustment of 6" to 17"
• Black or Silver powder coat finish

Cut sheet in PDF

Instruction Sheet

The VH-005 is an electronic component holder that attaches to either a pipe or ceiling mast. The VH-005 can attach to any size pipe from 1" to 2" OD pipe including all VMP ceiling masts. With a simple but robust design the VH-005 you can sure your electronic component is well supported.

• works with all VMP ceiling mounts and all manufacturers ceiling mounts using masting from 1" to 2" O.D.
• accommodates DVD players, CD players, DVR's, HD receivers, VCR's, and other electronic components
• mounting U "tray" extends 13" from the pipe
• includes decorative plastic covers
• load capacity - 25 lbs
• VH005 - silver powder coat finish
• VH005B - black powder coat finish

A&E Spec Sheet

Instruction Sheet

The EXT-1830 is a universal adaptor to work with all VMP ceiling mounts and most other manufacturers ceiling mounts that can use 1.5" NPT pipe. The adaptor is adjustable in length and pre-threaded.

• Works with VMP ceiling mounts that use or have been adapted to use 1.5" NPT pipe
• Work with any manufacturers' ceiling mounts which use 1.5" NPT pipe
• Adjustable from 18" to 30"
• Black powder coat finish

EXT-4872 - Same as above except adjustable from 48" to 72" in length

A&E Spec Sheet: EXT-1830

A&E Spec Sheet: EXT-4872

The EXT-A/B is an easy to install extension pipe that works as an in-line splice to extend the drop length on ceiling mounts.

EXT-A

• Acts as an inline splice to extend drop length of VMP014/024, LCD-2537C and PM Series (except PM-LP) by up to 28" (can be cut to length)
• 31" tempered steel mast
• Black powder coat finish

EXT-B

A&E Spec Sheet: EXT-A

A&E Spec Sheet: EXT-B

Schematic

The IBA-1 is an easy to use device to adapt any VMP ceiling mount to an I-Beam. It can also be used with other mounting brands that use a 1.5" NPT pipe.

• Designed to adapt ceiling mounts to clamp to an I-Beam
• Works with all VMP ceiling masts directly
• Will also work with all manufacturer's mounting systems when using 1.5" NPT pipe
• Accommodates 2.25" to 12" flange widths
• Accommodates maximum flange height of 1"
• Black powder coat finish

A&E Spec Sheet

Instruction Sheet

The ER-1 is an EIA compliant, 19-Inch headend steel constructed equipment rack with a rail height of 71" and 40 available rack spaces.

• Rail height: 71" / 40 rack spaces
• EIA compliant
• Standard 10-32 threading
• Includes 32 rack screws
• Steel construction
• Load capacity: 400 lbs evenly distributed
• Black static resistant powder coat finish

A&E Spec Sheet

Technical Drawing

Instruction Sheet

The ER-184-4PKIT is an expansion kit that converts the ER-184 from a two post rack to a four post rack.

• Converts ER-184 from 2 post to 4 post rack
• Includes side stabilizing bars
• Steel construction
• Black static resistant powder coat finish

A&E Spec Sheet

Technical Drawing

The ER-1-4PKIT is an easily installed expansion kit for the ER-1 rack to convert a two post rack to a four post rack.

• Converts ER-1 from 2 post to 4 post rack
• Includes side stabilizing bars
• Steel construction
• Black static resistant powder coat finish

A&E Spec Sheet

Technical Drawing

The ER-72 is and EIA compliant 19", open frame, heavy duty aluminum rack. It can accommodate 38 rack spaces and has a self squaring design.

• 38 rack spaces / EIA compliant
• Aluminum construction / Self squaring design
• Standard 10 - 32 threading
• Includes 32 rack screws
• Load capacity - 750 lbs evenly distributed
• Black powder coat finish

A&E Spec Sheet

Technical Drawing

The ER-148 is an EIA compliant, 19-Inch headend steel constructed equipment rack with a rail height of 48" and 27 available rack spaces.

• Rail height - 48" / 27 rack spaces
• EIA compliant
• Standard 10-32 threading
• Includes 32 rack screws
• Steel construction
• Load capacity - 400 lbs evenly distributed
• Black static resistant powder coat finish

A&E Spec Sheet

Instruction Sheet

Technical Drawing

The ER-84 is and EIA compliant 19", open frame, heavy duty aluminum rack. It can accommodate 45 rack spaces and has a self squaring design.

• 45 rack spaces / EIA compliant
• Aluminum construction / Self squaring design
• Standard 10 - 32 threading
• Includes 32 rack screws
• Load capacity - 750 lbs evenly distributed
• Black powder coat finish

A&E Spec Sheet

Technical Drawing

The ER-184 is an EIA compliant, 19-Inch headend steel constructed equipment rack with a rail height of 84" and 46 available rack spaces.

• Rail height - 84" / 46 rack spaces
• EIA compliant
• Standard 10-32 threading
• Includes 32 rack screws
• Steel construction
• Load capacity - 400 lbs evenly distributed
• Black static resistant powder coat finish

A&E Spec Sheet

Instruction Sheet

Technical Drawing

The ER-W24 is an EIA compliant, 13 Rack Space, 19-Inch steel and aluminum wall mounted equipment rack with a 24-Inch rail height and a 100 lb. load capacity.

• Rail height - 24"
• 13 rack spaces
• Usable depth - 19"
• EIA compliant
• Opens from either the left or the right side
• Fixed wall plate allows easy installation and removal of populated rack
• Innovative lift on/off design
• Standard 10-32 threading
• Steel and aluminum construction
• Load capacity - 100 lbs evenly distributed
• Black static resistant powder coat finish

A&E Spec Sheet

Instruction Sheet

Technical Drawing

The ER-8RSA is a patented adjustable rack shelf that can accommodate up to eight receivers. The shelf can be adjusted left to right and front to back to handle a wide variety of receiver brands and styles. The ER-8RSA also comes with additional components including front and top anti-roll bars and additional receiver separators.

Patent # 7,850,022

• Accommodates up to eight receivers
• Adjusts left to right and front to back
• Includes front and top anti-roll bars
• Load capacity - 50 lbs
• Includes 10-32 and 12-24 mounting screws
• Black powder coat finish

A&E Spec Sheet

Instruction Sheet

The ER-S2CM is a two space vented shelf that is center mounted. It can work with a variety of components, has a heavy load capacity and includes two sets of mounting screws.

• Fits components up to 17.375" wide
• Two space racking height (3.5")
• Tray depth - 19"
• Load capacity - 50 lbs
• Includes 10-32 and 12-24 mounting screws
• Black static resistant powder coat finish

A&E Spec Sheet

Technical Drawing

The ER-S1 is a two space economy rack shelf. It has a heavy load capacity and includes two sets of mounting screws.

• Fits components up to 17" wide
• Two space racking height (2.6")
• 12.5" tray depth
• Load capacity - 40 lbs
• Includes 10-32 and 12-24 mounting screws
• Black powder coat finish

A&E Spec Sheet

Technical Drawing

The ER-S2U is a two space rack shelf that can store components up to 17.375" wide and 14.75" deep. It has a load capacity of 50 lbs. and includes both #10-32 and #12-24 rack screws to attach the shelf.

• Fits components up to 17.375" wide
• Two space racking height (3.5")
• Tray depth - 14.75"
• Load capacity - 50 lbs
• Includes 10-32 and 12-24 mounting screws
• Black static resistant powder coat finish

A&E Spec Sheet

Technical Drawing

The ER-S1V is a vented two space rack shelf that can store components up to 17" wide and 12.5" deep. It has a load capacity of 40 lbs. and includes both #10-32 and #12-24 rack screws to attach the shelf.

• Fits components up to 17" wide
• Two space racking height (2.6")
• 12.5" tray depth
• Load capacity - 40 lbs
• Includes 10-32 and 12-24 mounting screws
• Black powder coat finish

A&E Spec Sheet

Technical Drawing

The ER-S2UV is a vented two space rack shelf that can store components up to 17.375" wide and 14.75" deep. It has a load capacity of 50 lbs. and includes both #10-32 and #12-24 rack screws to attach the shelf.

• Fits components up to 17.375" wide
• Two space racking height (3.5")
• Tray depth - 14.75"
• Load capacity - 50 lbs
• Includes 10-32 and 12-24 mounting screws
• Black static resistant powder coat finish

A&E Spec Sheet

Technical Drawing

The ER-HWB1 is a single spaced, hinged wall bracket that can be mounted to a rack or directly to a wall. Easy to use and allows access to the back of the panel.

• Provides easy access to the back of panels
• Right or left hand opening
• Depth - 4 "
• Includes 10-32 and 12-24 mounting screws
• Black anti-stat powder coat finish.

A&E Spec Sheet

The ER-HWB2 is a double spaced, hinged wall bracket that can be mounted to a rack or directly to a wall. Easy to use and allows access to the back of the panel.

• Provides easy access to the back of panels
• Right or left hand opening
• Depth - 4 "
• Includes 10-32 and 12-24 mounting screws
• Black anti-stat powder coat finish.

A&E Spec Sheet

The ER-DRCM1 can be easily mounted to any rack to manage all types and sizes of wire and cable.

• large slotted metal rings manage all types and sizes of wire and cable
• easy to install on equipment racks
• easy to assemble
• includes 10-32 and 12-24 mounting screws
• black anti-stat powder coat finish

A&E Spec Sheet

The ER-DRCM2 can be easily mounted to any rack to manage all types and sizes of wire and cable.

• large slotted metal rings manage all types and sizes of wire and cable
• easy to install on equipment racks
• easy to assemble
• includes 10-32 and 12-24 mounting screws
• black anti-stat powder coat finish

A&E Spec Sheet

The ER-1B blank plate is used to fill excess rackmountable space in your rack when future component expansion is anticipated.

• Tempered 16 gauge steel
• Black static resistant powder coat finish

A&E Spec Sheet

The ER-2B blank plate is used to fill excess rackmountable space in your rack when future component expansion is anticipated.

• Tempered 16 gauge steel
• Black static resistant powder coat finish

A&E Spec Sheet

The ER-4B blank plate is used to fill excess rackmountable space in your rack when future component expansion is anticipated.

• Tempered 16 gauge steel
• Black static resistant powder coat finish

A&E Spec Sheet

The ER-8B blank plate is used to fill excess rackmountable space in your rack when future component expansion is anticipated.

• Tempered 16 gauge steel
• Black static resistant powder coat finish

A&E Spec Sheet

A set of four heavy duty casters that can easily attach to most VMP racks.

• Four heavy duty casters that attach to the ER-1, ER-148 or ER-184
• Hole pattern - 2.375" x 3.375"
• Hardware to attach casters to rack included
• Maximum weight capacity of rack with casters - 400 lbs

A&E Spec Sheet

A set of 50 or 100 durable rack screws.

• 50 or 100 pack of screws
• 0.75" long with 10-32 threads
• Classic Phillips trim head
• Includes nylon washers
• Heat treated to resist stripping

The VMP-VWS is an easy to install, vented wall or backboard shelf. It has a heavy load capacity, static resistant powder coat finish, and incorporates five cable supply locations.

• Internal dimensions - 20.5" W x 17" D x 17" H
• Wall or backboard mount
• Convenient quick-slide assembly
• Five cable supply locations
• Load capacity - 200 lbs
• Black static resistant powder coat finish

A&E Spec Sheet