AK-1The AK-1 is an easy to use adaptor that converts VMP mounts to use 1.5" NPT pipe for longer installation ceiling drops.
LCD-PAThe LCD-PA is a pole adaptor used with the LCD-1 and LCD-2537 to enable these mounts to be attached to a round or square pole.
AK-1PTThe AK-1PT is an easy to use adaptor that converts VMP mounts to use 1.5" NPT pipe for longer installation ceiling drops. The unit works like the AK-1, but incorporates a cable pass through.
LVMP-1The LVMP-1 allows wall plates to be installed anywhere by doing away with the need for an electrical junction box.
AP-1The AP-1 VESA adaptor plate adapts a VESA 200mm plate to accommodate a VESA 400mm x 200mm hole pattern. Although the AP-1 has been designed specifically to work with VMP's LCD-2537 and LCD-2537C universal mid-size flat panel wall and ceiling mounts, it will work with any manufacturer's VESA 200mm mount.
SCFR-1The SCFR-1 is an easy to use finishing ring that easily clamps around both 1.5" NPT pipe and VMP ceiling masts that are not 1.5".
AP-2BThe AP-2B VESA adaptor plate adapts a VESA 200mm plate to accommodate a VESA 300mm x 300mm hole pattern. Although the AP-2B has been designed specifically to work with VMP's LCD-2537B and LCD-2537CB universal mid-size flat panel wall and ceiling mounts, it will work with any manufacturer's VESA 200mm mount.
SCM-1The SCM-1 is a suspended ceiling tray for ceiling mounts. The SCM-1 can be used with any VMP ceiling mount or any ceiling mount using 1.5" NPT pipe. Can be used to support projectors, flat panels or CCTV under 75 lbs. Tie wire, turnbuckles and attachment hardware included.
CCA-1A cathedral ceiling adaptor which works with the standard mast of the VMP014/024, VMP036/038, PM Series, LCD-2537C and PDS-LC or any mount which uses a 1.5" NPT mast.
UA-1The UA-1 is an easy to use device to adapt any VMP ceiling mount to a piece of Uni-strut®. It can also be used with other mounting brands that use a 1.5" NPT pipe.
CP-1/CP-2The CP-1 and the CP-2 are universal ceiling mount plates that will accommodate 1.5" and 1" NPT pipe. Used for extending ceiling drop lengths; the CP-1/CP-2 has multiple, pre drilled hole patterns to attach to a variety of ceilings.
UP-1The UP1 allows for 2 stud or joist span to distribute the mount and equipment weight evenly.
CP-1PTThe CP-1PT is a universal ceiling mount plate that will accommodate 1.5" NPT pipe. Used for extending ceiling drop lengths; the CP-1PT has multiple, pre drilled hole patterns to attach to a variety of ceilings with cable pass-through.
VH-001The VH-001 is an electronic component holder that attaches to many of VMP’s CRT mounts. Combined with a VH-004B, the VH-001 can be attached to VMP flat panel ceiling mounts. With a sturdy wrap around design you can be sure your equipment will be held well.
DVR-WAThe DVR-WA are a pair of heavy duty, easy to install DVR lockbox wall mounting arms.
VH-002The VH-002 is an add-on holder for the VH-001. The VH-002 allows for a second electronic component be installed below a VH-001.
ER-LCD1017The ER-LCD1017 can hold most 10" to 17" flat panels on an equipment rack. It can also accommodate up to a 23" monitor by inverting the mount on the rack. The ER-LCD1017 has a static resistant powder coat finish and includes two types of rack screws.
VH-003The VH003 wall mount component holder is a stylish way to hold DVD players, DVR's, HD receivers, CD players, VCR's and gaming systems (Xbox 360, Playstation 3, Nintendo Wii). The mount can be used for a single device or "stacked" for use with multiple devices. Integrated cable management system hides all cables for a clean look.
EXT-1830The EXT-1830 is a universal adaptor to work with all VMP ceiling mounts and most other manufacturers ceiling mounts that can use 1.5" NPT pipe. The adaptor is adjustable in length and pre-threaded.
VH-004The VH-004 is an adaptor to allow an electronic component holder to be hung underneath a VMP flat panel ceiling mount. Combined with the VH-001S, the VH-004 allows for adjustable drop distance so your electronic component can be just below your ceiling mounted flat panel.
EXT-A/EXT-BThe EXT-A/B is an easy to install extension pipe that works as an in-line splice to extend the drop length on ceiling mounts.
VH-005The VH-005 is an electronic component holder that attaches to either a pipe or ceiling mast. The VH-005 can attach to any size pipe from 1" to 2" OD pipe including all VMP ceiling masts. With a simple but robust design the VH-005 you can sure your electronic component is well supported.
IBA-1The IBA-1 is an easy to use device to adapt any VMP ceiling mount to an I-Beam. It can also be used with other mounting brands that use a 1.5" NPT pipe.
IWB-1BThe IWB-1B is an in wall box adaptor that allows up to a 37" flat panel to fully collapse into a wall. It installs easily between two 16" on center wooden studs, has integrated cable and electrical knockouts and a high load capacity. The IWB-1B works with the LCD-1(B) and LCD-2537(B) mounts.
Become a fan